MT7688平台运行Openwrt18.06版本；
mt7688的rt305x-esw交换芯片有6个交换接口，其中一个和CPU内核连接，其余可通过RJ45接口引出，手里的开发板只引出其中3个口，这3个口一个作为wan口，其余两个作为lan口；
假定平台虚拟网卡eth0，划分了2个Vlan，则对应为eth0.1, eth0.2;
wan口与lan口需要在不同的Vlan下；
从源码配置平台的wan口lan口：
路径 ：openwrt\target\linux\ramips\base-files\etc\board.d
修改02_network文件内容：查找mt7628，然后修改
"0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "6@eth0"
为
"0:wan" "1:lan" "2:lan" "3:lan" "4:lan" "6@eth0"
[此项修改是因为手里的板子引出来的WAN口RJ45接头坏了，所以将WAN口从新绑定到Lan0口上去，在源码上修改后就不用每次烧录代码后去手动绑定]
重新烧录固件；登录openwrt的web界面部分配置如下：
1. 配置eth0.2 vlan下的交换接口作为lan口；
2. 配置eth0.2 vlan下的口为Wan口，并且使能DHCP client（如果mt7688是作为二级路由接入网络，并且上级路由使能了DHCP服务）
3. 配置Vlan（Wan口和Lan口需要处在不同的Vlan下，我把Wan口设在Vlan1下，Lan口设置在Vlan2下，分别对应eth0.1和eth0.2）此处设置的是MT7688内置的交换芯片的交换接口，需要对照电路原理图找到和板子RJ45接头的对应关系
配置结束……
注：openwrt\target\linux\ramips\base-files\etc\board.d\02_network文件内的"0:wan" "1:lan" "2:lan" "3:lan" "4:lan" "6@eth0"与上图的交换接口并不是一一对应关系，而是与下面一一对应：
root@OpenWrt:/# swconfig list Found: switch0 - rt305x root@OpenWrt:/# swconfig dev switch0 show Global attributes: enable_vlan: 1 alternate_vlan_disable: 0 bc_storm_protect: 0 led_frequency: 0 Port 0: disable: 0 doubletag: 0 untag: 1 led: 5 lan: 1 recv_bad: 0 recv_good: 37417 tr_bad: 0 tr_good: 9008 pvid: 1 link: port:0 link:up speed:100baseT full-duplex Port 1: disable: 0 doubletag: 0 untag: 1 led: 5 lan: 1 recv_bad: 0 recv_good: 12971 tr_bad: 0 tr_good: 19506 pvid: 2 link: port:1 link:up speed:100baseT full-duplex Port 2: disable: 0 doubletag: 0 untag: 1 led: 5 lan: 1 recv_bad: 0 recv_good: 0 tr_bad: 0 tr_good: 0 pvid: 2 link: port:2 link:down Port 3: disable: 0 doubletag: 0 untag: 1 led: 5 lan: 1 recv_bad: 0 recv_good: 0 tr_bad: 0 tr_good: 0 pvid: 2 link: port:3 link:down Port 4: disable: 0 doubletag: 0 untag: 1 led: 5 lan: 1 recv_bad: 0 recv_good: 0 tr_bad: 0 tr_good: 0 pvid: 2 link: port:4 link:down Port 5: disable: 1 doubletag: 0 untag: 0 led: ??? lan: 1 recv_bad: 0 recv_good: 0 tr_bad: 0 tr_good: 0 pvid: 0 link: port:5 link:down Port 6: disable: 0 doubletag: 0 untag: 0 led: ??? lan: ??? recv_bad: ??? recv_good: ??? tr_bad: ??? tr_good: ??? pvid: 0 link: port:6 link:up speed:1000baseT full-duplex VLAN 1: ports: 0 6t VLAN 2: ports: 1 2 3 4 6t
让板子默认使能WIFI功能：
修改路径openwrt\package\kernel\mac80211\files\lib\wifi下的mac80211.sh文件内容：
set wireless.radio${devidx}=wifi-device
set wireless.radio${devidx}.type=mac80211
set wireless.radio${devidx}.channel=${channel}
set wireless.radio${devidx}.hwmode=11${mode_band}
${dev_id}
${ht_capab}
set wireless.radio${devidx}.disabled=1
set wireless.default_radio${devidx}=wifi-iface
set wireless.default_radio${devidx}.device=radio${devidx}
set wireless.default_radio${devidx}.network=lan
set wireless.default_radio${devidx}.mode=ap
set wireless.default_radio${devidx}.ssid=OpenWrt
set wireless.default_radio${devidx}.encryption=none
为：
set wireless.radio${devidx}=wifi-device
set wireless.radio${devidx}.type=mac80211
set wireless.radio${devidx}.channel=${channel}
set wireless.radio${devidx}.hwmode=11${mode_band}
${dev_id}
${ht_capab}
set wireless.radio${devidx}.disabled=0
set wireless.default_radio${devidx}=wifi-iface
set wireless.default_radio${devidx}.device=radio${devidx}
set wireless.default_radio${devidx}.network=lan
set wireless.default_radio${devidx}.mode=ap
set wireless.default_radio${devidx}.ssid=OpenWrtTest
set wireless.default_radio${devidx}.encryption=psk2
set wireless.default_radio${devidx}.key=123456
重新编译固件烧录，开机后默认使能wifi，wifi认证方式为WPA2-PSK,密码为123456 ，wifi ssid为OpenWrtTest
转载于:https://www.cnblogs.com/weishengzhong/p/11005021.html