1、软件

1.spyder

2.Gprmax

2、代码及解释

1.首先在spyder中编辑好python部分代码，代码如下：主要是确定含水量、半径、深度三个部分，随机生成需要的范围内的数据；

import scipy.interpolate
import numpy as np
from random import  random as rd

m=np.array([12,9.3,6.2,5.5,2.8,0.2])
e_stat = np.array([12.84,11.19,9.14,8.63,6.75,4.814])
e_inf = np.array([7.42,7.2,5.93,6.023,5.503,4.507])
t = np.array([0.611,0.73,0.8,1,2.28,0.82])*10**-9
sigma = np.array([20.6,23,6.7,5.15,2.03,0.606])*10**-3

es = scipy.interpolate.interp1d(m, e_stat)
ei = scipy.interpolate.interp1d(m, e_inf)
t0 = scipy.interpolate.interp1d(m, t)
si = scipy.interpolate.interp1d(m, sigma)

mv=0.2+11.8*rd()

print("#material:{} {} 1 0 concrete \n".format(ei(mv), si(mv)))
print("#add_dispersion_debye: 1 {} {} concrete \n".format(es(mv)-ei(mv), t0(mv)))

print("#box: 0 0 0 0.5 0.3 0.3 concrete \n")

r=0.005 + 0.0245*rd()
z=(0.3-r)*rd()
print("#cylinder: 0.25 0 {} 0.25 0.3 {} {} pec \n".format(z,z,r))

2.生成结果：每次都随机生成含水量、半径、深度，含水量有Debye模型来确定；

3.整合到gprmax中可批量生成，代码如下：

#domain: 0.5 0.3 0.4
#dx_dy_dz: 0.001 0.001 0.001
#time_window: 3000

#python:
import scipy.interpolate
import numpy as np
from random import  random as rd

m=np.array([12,9.3,6.2,5.5,2.8,0.2])
e_stat = np.array([12.84,11.19,9.14,8.63,6.75,4.814])
e_inf = np.array([7.42,7.2,5.93,6.023,5.503,4.507])
t = np.array([0.611,0.73,0.8,1,2.28,0.82])*10**-9
sigma = np.array([20.6,23,6.7,5.15,2.03,0.606])*10**-3

es = scipy.interpolate.interp1d(m, e_stat)
ei = scipy.interpolate.interp1d(m, e_inf)
t0 = scipy.interpolate.interp1d(m, t)
si = scipy.interpolate.interp1d(m, sigma)

mv=0.2+11.8*rd()

print("#material: {} {} 1 0 concrete \n".format(ei(mv), si(mv)))
print("#add_dispersion_debye: 1 {} {} concrete \n".format(es(mv)-ei(mv), t0(mv)))

print("#box: 0 0 0 0.5 0.3 0.3 concrete \n")

r=0.005 + 0.0245*rd()
z=(0.3-r)*rd()
print("#cylinder: 0.25 0 {} 0.25 0.3 {} {} pec \n".format(z,z,r))

filename="concrete_labels"
f=open(filename,'a')
f.write("{}: {} {} {}".format(current_model_run, r,z,mv))

#定义天线
from user_libs.antennas import GSSI
GSSI.antenna_like_GSSI_1500(0.25,0.15,0.3,resolution=0.001)

#end_python:
#geometry_view: 0 0 0 0.5 0.3 0.4 0.002 0.002 0.002 geo n

 4.输入指令在gprmax中执行改输入文件：

• python -m gprMax ×××（文件名）-n 2000  ,这个两千是指模型数量

4、结果

最后结果会生成你所定义的模型数量的out文件；